Just looking for a Mic for my Kenwood ts-570. The base of my old MC60 has crapped out and I need a replacement.
I am also open to suggestions on what kind of mic to look for. I do need to try and keep it on the cheap side being a cheap ass ham ....
Just looking for a Mic for my Kenwood ts-570. The base of my old MC60 has crapped out and I need a replacement.
I am also open to suggestions on what kind of mic to look for. I do need to try and keep it on the cheap side being a cheap ass ham ....
a yankee living in the hind end of the bible belt
some people are like slinkys, not really good for anything, but still bring a smile to your face when you push them down the stairs.
4 pin or 8?
I am surprised at such a sudden deterioration in a woman whose only ailment was a lazy anus.
That should be an 8 pin.
“Nobody is going to feel sorry for us. 90% of the people don’t care, the other 10% are glad it happened.” — Clint Hurdle, 2019
BAN THE DH!
Fudd's First Law of Opposition: If you push something hard enough, it WILL fall down.
Teslacle's Deviant to Fudd's Law: It goes in, it must go out.
Just remember: Abraham Lincoln didn't die in vain. He died in Washington, DC
Cutch 300!!!!!
“Nero fiddled while Rome burned. Trump golfed.” — Bernie Sanders
Quando Omni Flunkus Moritati
Yes, 8 pin. Are you looking for a stock type hand mike, desk mic or are you willing to experiment.
I can probably help you out. I have a TS-570S and here lately I have been experimenting with some cheap assed mics and have been getting great results.
I see now that the title says DESK MIC..... somehow I missed that.
Last edited by KA9MOT; 10-07-2012 at 08:53 PM.
"One man with courage makes a majority." ~ Andrew Jackson
Steve KA9MOT
Macomb, IL
Yes, looking for a desk mic or parts for the base of the mc-60... It is and 8 pin on the 570dg.
a yankee living in the hind end of the bible belt
some people are like slinkys, not really good for anything, but still bring a smile to your face when you push them down the stairs.
Uh, that would be an 8 pin.
An 8 pin that utilizes that hard to reach with a soldering iron center pin.
I believe a 1000 ohm studio mic can be tailored through the menu system to have high and low cut offs as well as mid-range peaking.
I've enjoyed island life for 17 years. That's 13 years more than the Confederacy was around.
RIP Albi
When do you tell a woman you're a ham?
It's a jungle out there. Many EQ stupidly with poor articulation.
~TKX
YIAH
"And, of course, the Gym Teacher being his usual self."
W3WN
"The enablers ride on the top of the pile."
WZ7U
Let me see what I can come up with. I happen to have a generic vocal mic I'll wire up and see how well it works. I don't have much in it. Do you have a foot or hand PTT switch?Originally Posted by kb2crk
IMG_20121008_004630.jpgIMG_20121008_004638.jpg
Last edited by KA9MOT; 10-08-2012 at 12:53 AM.
"One man with courage makes a majority." ~ Andrew Jackson
Steve KA9MOT
Macomb, IL
Yes, to all of the above. The center pin is a ground and is not that hard to reach. Menu #14 is TX EQ
Last edited by KA9MOT; 10-08-2012 at 01:05 AM.
"One man with courage makes a majority." ~ Andrew Jackson
Steve KA9MOT
Macomb, IL
The only mic switch I had was the one on the mc60. The microphone part itself works fine but it is a pain to work the small slide switch on the back of it. The base has some issues where the audio is not making it through all the time or comes out with distortion. neither one is good.
a yankee living in the hind end of the bible belt
some people are like slinkys, not really good for anything, but still bring a smile to your face when you push them down the stairs.
I have a couple MC85s I'm planning to sell.
"Everyone wants to be an AM Gangsta until it's time to start doing AM Gangsta shit."
Posting Permissions
Reply With Quote