PDA

View Full Version : MSM5564 datasheet and a Yasue FT-225RD Counter fault.



EI0DB
08-18-2011, 08:00 AM
Found this community and "Hardware Hackin' the oldies". It came up in a Google search for MSM5564. While searching for a datasheet for the MSM5564 clock chip in the Ft-225RD counter. If anyone has the datasheet would appreciate a copy and any comments on my problem.

I have a FT-225RD that has been off the air for a "few" years after I was in an accident, I am attempting to bring back to life and spec as I could find no repair outfit in the UK who was prepared to sort it for me. :(

The transmitter is on frequency and stable reports say mod is OK, but the built-in counter display is free running on switch on, before settling either on the correct reading or some 2300 Kcs low/high more often low and will stay like that for hours steady.
I now have a DFM and with the Tx on 145.000 (R0), checking around the counter I can see the crystal is oscillating but on 1.310678 Mhz (TP1) (not 1.31072 even when locked, TP2 shows a variable squarish wave 1 to 9 Hz and 5 Hz when locked. At this point I suspect either the MSM5546 or the crystal. Also wonder how critical the 5 volt voltage is, I read 4.8 volts on pin 8 of the MSM5564 ?

Anyone who has seen this fault, has the datasheet please. regards, Dave.:)

N8YX
08-18-2011, 08:39 AM
Dave,

Welcome!

I'm going to save you a bit of trouble re: that counter. There's a JA who has developed a PIC-based replacement for the MSM5564 as used in the FT-902, FT-101ZD...and one might be able to retrofit it to the FT-225/625 lines. Let me do a little digging...

WØTKX
08-18-2011, 09:34 AM
Hey, here's a linky... http://www.nam-arc.org/cms/index.php?idart=154&changelang=2

EI0DB
08-18-2011, 01:20 PM
Hi, Thank you for the replies and the link. The fixes shown will not solve my problem as the MSM5546 (my problem) is providing the gate signal. Once my 225RD locks all digits are displayed OK. I have a replacement chip "on the shelf" for the decade counter the PIC chip fix is for. I found a better explanation of the counter internals in the YC-601 Handbook located this evening, looks as if there should be a 5Hz pulse Have tried all the datasheet sites Google has turned up and have found "zero" on the MSM5546 as if it never existed. I have even found a source for the chip in the far east, but no data sheet. I have not got much hair left, but I am pulling it on this one (hi!). Thanks again, Dave

N8YX
08-18-2011, 06:52 PM
A bit of decompress and thought on the matter:

It sounds like the 1.31072MHz crystal (which determines the reference oscillator/gating frequency) has drifted and its load capacitance is changing with heat. Not uncommon with these, it seems. Does the 225's counter circuit incorporate a trimmer and/or a padder capacitor (of around 6-20pF) across the crystal? If a trimmer, can it be adjusted sufficiently to net the oscillator properly?

WØTKX
08-18-2011, 08:00 PM
That's a good call John-Fred. ;) And likely that "disappeared" chip is OK, which is a good thing. I saw the Fox Tango website had the YC-601 using that chip as well. Wondered if it used a similar circuit. There are data sheets out there, for $32. Bastids.

Have you tried asking at the Fox Tango Forum? http://www.foxtango.org/phpBB2/index.php

N8YX
08-19-2011, 03:43 AM
Belay my PIC comments - I got that part confused with the OKI LSI counter chip which was used in the 101ZD/902 series.

The '5564 is present in the FT-901's counter circuit and I know that one all too well.

It's a CMOS binary up counter which has a max modulus of 524K and is used to divide the reference oscillator signal down to 5Hz. 4.8V on pins 7 and 8 should be fine. The crystal and/or the two capacitors associated with it (typ: 51p to ground on the clock pins 1 and 2) are suspect.

Look at pins 3, 4, 5,6, 9 and 10 with a scope - what do you see, and is it stable?

ETA:

Pin 8 looks to be the divisor setting pin, if chip lead convention is any indication. Tied to 5v it configures the chain as /4. Grounded, /2. (The only other option is Pin 7, and I strongly suspect it's for the +5v supply.)

WØTKX
08-19-2011, 09:26 AM
That chip is in the FT-902DM as well?

N8YX
08-19-2011, 11:40 AM
That chip is in the FT-902DM as well?

No - the '902 uses a custom Oki counter/display driver chip. The '901 and '225/'625 implemented their readout with discretes, and one of them happens to be the '5564. I thought Yaesu had switched to the single-chip solution in their VHF equipment but it now appears that the counter assembly is almost identical to that of the earlier rigs.

EI0DB
08-20-2011, 08:55 AM
Looks like my post from last night failed to complete. First can I have the URL where the MSS5564 datasheet is found I am happy to pay for the info if that is the only source. I spent time yesterday going over the pins of the MSM5564 with DFM and scope. The 5 Volt line reads 4.78 volts steady (measured with Fluke 77 Multimeter), on pins 7 and 8 as was suggested. The oscillator on pins 1 and 2 read consistently (for an hour) 1310.67 KHz. The frequency on the other pins all vary. Pin 10 4-6 Hz, pin 12 10-13 Hz, pin 13 20-23 Hz. I have ordered a pack of replacement 51pF disc ceramics 5% 50V, and ordered replacement MSM5564 chip as I would like to bring the counter back to original as far as possible. On the scope I can see a 10 mV, 1.28 Mhz distorted sine wave on Pin 10, but no 5HZ +/- clock signal. So I will have to wait for the parts to come over from the Far East ( how long is a piece of string hi!).

K7SGJ
08-20-2011, 09:09 AM
And here I thought How Long was a Chinaman.

N8YX
08-20-2011, 09:16 AM
The oscillator on pins 1 and 2 read consistently (for an hour) 1310.67 KHz.
This looks to be a problem.

The oscillator should be exactly 1.31072 MHz. Anything else will definitely impact the gating pulse frequency - which should be 5hz. The fact that you are seeing jitter on the other pins also tells me that something is amiss with the crystal.

Yaesu may still stock them:


P/N H0100052

EI0DB
09-20-2011, 10:48 AM
Hi guys, Progress on the FT-225RD, the covers have arrived from the paint shop. So only the counter problem remains. The MSM5564s arrived no problem, I inject a 5HZ at the TP, and the counter locks, on that basis I guess the chances are 99% the crystal is off. Contacted Yaesu, who replied they do not have that part number any more and have still have not found a source for a full datasheet for the MSM5564 that shows the pinout and divide ratio programming. Anyone have a URL to this datasheet, I am quite willing to pay for the info, but cannot find it on the Web. Also can you suggest which outfit I should get to grind me a new 1310.72 Khz crystal as it's not the sort of item I have ever needed in the past. 73s Dave

WØTKX
09-20-2011, 12:35 PM
Hopefully recent activity, looks like the chip may be available, and the datasheet:

http://www.1sourcecomponents.com/partinfo/MSM5564.htm

http://www.sierraic.com/store.php/buy_online/parts/msm5564

K7SGJ
09-20-2011, 12:44 PM
Hi guys, Progress on the FT-225RD, the covers have arrived from the paint shop. So only the counter problem remains. The MSM5564s arrived no problem, I inject a 5HZ at the TP, and the counter locks, on that basis I guess the chances are 99% the crystal is off. Contacted Yaesu, who replied they do not have that part number any more and have still have not found a source for a full datasheet for the MSM5564 that shows the pinout and divide ratio programming. Anyone have a URL to this datasheet, I am quite willing to pay for the info, but cannot find it on the Web. Also can you suggest which outfit I should get to grind me a new 1310.72 Khz crystal as it's not the sort of item I have ever needed in the past. 73s Dave
Try International Crystal http://www.icmfg.com/

or Jan Crystal http://www.jancrystals.com/frequencies.html

I've used both in the past and was happy with the product.

73

N8YX
09-20-2011, 05:13 PM
Try International Crystal http://www.icmfg.com/

or Jan Crystal http://www.jancrystals.com/frequencies.html

I've used both in the past and was happy with the product.

73
International is who I used when I needed a crystal for the FT-901DM's counter: $100 (gulp!) plus shipping. It was a 655.36KHz rock, and they said anything below 1 MHz will be much higher than anything above.

K7SGJ
09-20-2011, 05:19 PM
Yikes!

WØTKX
09-20-2011, 07:23 PM
Kind of an odd frequency.

K7SGJ
09-20-2011, 07:24 PM
As opposed to even.

N8YX
09-21-2011, 10:55 AM
Kind of an odd frequency.

Not at all. Use it as the reference for a modulo-14 ripple counter...do the math...and tell us what frequency you end up with at stages 12 and 13...

WØTKX
09-21-2011, 11:21 AM
Oh, I meant "odd" as far as (inexpensively) finding the darn thing. It makes sense otherwise.

W3WN
09-22-2011, 07:47 AM
And here I thought How Long was a Chinaman.I thought How Long was an ex-NFL player now a talking head on the Fox NFL Pregame show?

Oh, sorry, that's Howie Long. Never mind.

EI0DB
09-22-2011, 09:51 AM
Ok, have send request to both outfits see what I get back. In this case the division is 2 to the 18, or  divide by 262144 and from 1310.72 Kcs the end point is (or should be) a nice 5Hz.